J-B WELD is the world's finest cold-weld compound. It's a remarkably easy, convenient, and inexpensive alternative to welding, soldering, and brazing. J-B WELD is the smart way to repair something ... and for literally pennies per use. When welding or soldering is out of the question due to cost, down time for repairs, or technical/environmental considerations, J-B WELD is the answer. Tel 020 8648 3866     (We stock all products) 


J-B WELD  8265

  Strong Metal Glue to Glue Metal


J-B WELD can be formed, drilled, ground, tapped, machined, filled, sanded, and painted. It stays pliable for about 30 minutes after mixing, sets in 4-6 hours, and cures fully in 15-24 hours. It's water-proof; petroleum-, chemical-, and acid-resistent; resists shock, vibration, and extreme temperature fluctuations, and withstands temperatures up to 500° F. J-B WELD is super strong, non-toxic, and safe to use. Before it sets, you can clean up with soap and water.

   
£7.99



J-B KWIK     8276


  Strong Metal Glue to Glue Metal
Fast Bonding - Set in just 4 minutes

J-B KWIK can be formed, drilled, ground, tapped, machined, filled, sanded, and painted. It stays pliable for about 2 minutes after mixing, sets in just 4 minutes, and cures fully in 4 hours. It's water-proof, petroleum-, chemical-, and acid-resistent; resists shock, vibration, and extreme temperature fluctuations, and withstands temperatures up to 300° F. J-B KWIK is super strong, non-toxic, and safe to use. Before it sets, you can clean up with soap and water.

No clamping is needed. Only minimal pressure while setting.
 £7.99  


Industro Weld -  J-B WELD   8280     " BIG SIZE" 10 oz

 
Strong Metal Glue to Glue Metal

INDUSTRO WELD is J-B WELD in an economical shop-size package containing two 5-oz. tubes. Professionals in many industries use it to fix, bond, or fill -- in the shop, factory, or field. INDUSTRO WELD makes strong, permanent repairs when hot welding isn't possible or practical.
J-B WELD can be formed, drilled, ground, tapped, machined, filled, sanded, and painted. It stays pliable for about 30 minutes after mixing, sets in 4-6 hours, and cures fully in 15-24 hours. It's water-proof; petroleum-, chemical-, and acid-resistent; resists shock, vibration, and extreme temperature fluctuations, and withstands temperatures up to 500° F. J-B WELD is super strong, non-toxic, and safe to use. Before it sets, you can clean up with soap and water.
   
£14.99


8 J-B Stik  8267-S

 

J-B Stik Weld is a hand kneadable, steel-reinforced epoxy putty adhesive/sealant that will plug holes and make permanent repairs on wet and dry surfaces. It will even cure completely submerged in water or GASOLINE! Simply knead thoroughly, with your fingers, a portion necessary for the repair and apply. J-B Stik will fully cure 20-30 minutes; and can be drilled, sanded, filed, tapped, machined, and painted. J-B Stik requires no tools or "prep time", and makes no mess. Use J-B STIK as an adhesive, laminate, plug, filler, sealant, and electrical insulator. Clean surface to be bonded. Apply J-B STIK, and let it cure. That's all there is to it!

It stays pliable for about 30 minutes after mixing, sets in 4-6 hours, and cures fully in 15-24 hours. It's water-proof; petroleum-, chemical-, and acid-resistent; resists shock, vibration, and extreme temperature fluctuations, and withstands temperatures up to 500° F. J-B STIK is super strong, non-toxic, and safe to use. Before it sets, you can clean up with soap and water

What does it bond to

Virtually any combination of iron, steel, copper, aluminum, brass, bronze, pewter, porcelain, ceramic, marble, glass, PVC & ABS, concrete, fiberglass, wood, fabric, paper -- just about any porous and non-porous material.

7.99  



 

 

 



More Detailed  Infomation

J-B WELD

 



   

How does it work?

J-B WELD is packaged in two tubes. One contains liquid steel/epoxy resin, and the other contains hardener. When mixed together in equal portions, a chemical reaction occurs that turns the mixture into a compound as hard and tough as steel -- and with similar properties.


How to use it:

Use J-B WELD as an adhesive, laminate, plug, filler, sealant, and electrical insulator. Squeeze out equal portions from the black and red tubes. Mix thoroughly. Clean surface to be bonded. Apply J-B WELD, and let it cure. That's all there is to it!

Like metal, J-B WELD can be formed, drilled, ground, tapped, machined, filled, sanded, and painted. It stays pliable for about 30 minutes after mixing, sets in 4-6 hours, and cures fully in 15-24 hours. It's water-proof; petroleum-, chemical-, and acid-resistent; resists shock, vibration, and extreme temperature fluctuations, and withstands temperatures up to 500° F. J-B WELD is super strong, non-toxic, and safe to use. Before it sets, you can clean up with soap and water. 

Uses

What does it bond to?

Virtually any combination of iron, steel, copper, aluminum, brass, bronze, pewter, porcelain, ceramic, marble, glass, PVC & ABS, concrete, fiberglass, wood, fabric, paper -- just about any porous and non-porous material.


How to Apply J-B WELD

Instructions:

MIXING: J-B WELD consists of two parts. Squeeze equal parts from each tube onto any clean disposable surface. Mix together thoroughly. A wooden dowel or paddle is a good mixing tool.

PREPARING SURFACE: Surface for application must be clean, dry, and free of dirt, grease, oil, etc. Remove any paint, primer, rust, etc. before applying J-B WELD. For the best weld, roughen surfaces to be welded with fine or course sandpaper.

APPLICATION: Apply with putty knife, spoon, wooden paddle, or other suitable tool. Avoid contact with skin and eyes. May be applied in an even coat, weld bead, or extruded shape as needed.

DRYING: Allow 4-6 hours for drying before handling. Allow to dry overnight (approximately 15 hours) before putting object to use. J-B WELD works faster if used in a room with a temperature above 50 F. After J-B WELD has cured for six hours, a heat lamp or light bulb placed near the weld will speed drying time.

IMPORTANT: In hot weather or in a very warm room, let J-B WELD set up or dry for about 15 to 20 minutes after mixing. This lets it thicken and prevents running or sagging. In cold weather, a heat lamp or light bulb placed close by will hasten drying time.


Properties (psi)
Tensile Strength: 3960
Adhesion: 1800
Flex Strength: 7320
Tensile Lap Shear: 1040
Shrinkage: 0.0%
Resistant to: 500° F

J-B KWIK


   
   


Description:

J-B KWIK is the perfect partner for the J-B WELD you keep in your tool box. Lots of times, you need to fix something fast and don't have the time or patience to hold it for half an hour while the hardener sets up, or wait for it to cure overnight. That's why there's J-B KWIK!

How does it work?

J-B KWIK is packaged in two tubes. One contains liquid steel/epoxy resin, and the other contains hardener. When mixed together in equal portions, a chemical reaction occurs that turns the mixture into a compound as hard and tough as steel -- and with similar properties.

Because J-B KWIK cures so fast, it's not as strong or as heat-resistant as the original J-B WELD. For typical household maintenance and repairs, however, it's just about perfect. Many happy customers have told us they were finally able to repair annoying things around their homes when, for years, nothing else worked. We think you'll find J-B KWIK as magical and practical in your home, too.


How to use it:

Use J-B KWIK as an adhesive, laminate, plug, filler, sealant, and electrical insulator. Squeeze out equal portions from the black and orange tubes. Mix thoroughly. Clean surface to be bonded. Apply J-B KWIK, and let it cure. That's all there is to it!

Like metal, J-B KWIK can be formed, drilled, ground, tapped, machined, filled, sanded, and painted. It stays pliable for about 2 minutes after mixing, sets in just 4 minutes, and cures fully in 4 hours. It's water-proof, petroleum-, chemical-, and acid-resistent; resists shock, vibration, and extreme temperature fluctuations, and withstands temperatures up to 300° F. J-B KWIK is super strong, non-toxic, and safe to use. Before it sets, you can clean up with soap and water.


Uses

What does it bond to?

Virtually any combination of iron, steel, copper, aluminum, brass, bronze, pewter, porcelain, ceramic, marble, glass, PVC & ABS, concrete, fiberglass, wood, fabric, paper -- just about any porous and non-porous material.


How to Apply J-B KWIK

Instructions:

MIXING: J-B KWIK consists of two parts. Squeeze equal parts from each tube onto any clean disposable surface. Mix together thoroughly. A wooden dowel or paddle is a good mixing tool.

PREPARING SURFACE: Surface for application must be clean, dry, and free of dirt, grease, oil, etc. Remove any paint, primer, rust, etc. before applying J-B KWIK. For the best weld, roughen surfaces to be welded with fine or course sandpaper.

APPLICATION: Apply with putty knife, spoon, wooden paddle, or other suitable tool. Avoid contact with skin and eyes. May be applied in an even coat, weld bead, or extruded shape as needed.

DRYING: IMPORTANT: Mix only the amount that will be needed, as the mixture sets in 4 minutes. If the temperature is below 40 F, setting time is longer. The mixture will become warm while it sets. No clamping is needed. Only minimal pressure while setting.