Shoe Goo - shoe repair
!!!Glue your shoe!!!
 |
|
| £6.99 |
Colour - Clear or Black
|
Shoe Goo is a
superior no mess adhesive and sealant that easily and permanently repairs all
types of footwear. It adheres to all kinds of materials, so use Shoe Goo to
mend rubber soles, tears in canvas or leather tops or to stop shoe laces from
fraying.
It dries to a waterproof, flexible rubber, so it will repair
waders and boots without breaking or cracking. Choose between Black or Clear
Apply directly from the tube to worn out areas and harden
overnight.
No mess. Permanent long lasting repair.
Repair damage heels and toes shoe soles.
Secures loose insoles.
Coats frayed shoe laces.
Shoe GOO is an
adhesive specially formulated with extra abrasion resistance and thickness to
extend the life of all kinds of shoes.
Repairs and protects shoes of all types: leather, rubber,
canvas, and shoelaces too!
Strong enough for gym and sports shoes.
Shoe GOO Tips
Waterproofing:
Shoe GOO is water resistant immediately upon application. Apply Shoe GOO
directly to the surface to be sealed. Use thin coats of Shoe GOO to build a
thick coating on the surface to be sealed, allowing each layer to set 3 to 4
hours. This is especially ideal for smooth surfaces, such as plastic, glass or
ceramic. Shoe GOO hardens by solvent evaporation, so allow time for thorough
hardening to ensure proper bonding and wear resistance.
Repairing worn soles:
If a worn shoe has a hole that goes all the way through the sole, tape over the
hole inside the shoe before applying Shoe GOO to the outer sole. This will help
avoid creating a bump. The tape should be removed from the inside and all bumps
smoothed out within 2 hours, before the glue is completely hard.
Fishing and foul weather
gear: Some fisherman's waders and foul weather gear have a water-repellent
coating that must be removed before Shoe GOO will adhere. Scrub the area with
detergent and allow to dry. Roughen surface before applying Shoe GOO. If the
bond still pulls apart, the repair must be done on the inside surface of the
item, which is usually reinforced with fabric.
Use Shoe GOO to:
Rebuild your worn-out soles overnight.
Seal rubber boots, galoshes, and waders.
Coat and protect shoes to avoid premature wear.
Repair damaged heels.
Secure loose insoles.
Reinforce skate shoes.
Coat skateboards for extra traction.
Directions:
Please read all directions before using. SHOE GOO should be
used in a well-ventilated area.
Surface should be clean, dry and free of dirt. For best
results, roughen surface before use. Best when used between 70°F and 85°F.
Puncture seal at the top of the tube using the pointer cap.
Always test a small area to ensure proper application
technique and dry time. Prolonged exposure to warm water may cause
discoloration and possible loss of adhesion when exposed to chemicals used in
hot tubs and poolsespecially in outdoor locations. May be weakened by contact
with certain highly plasticized materials.
Apply SHOE GOO directly to each surface to be bonded or
repaired. Allow SHOE GOO to partially cure, 2-10 minutes, before bringing
surfaces together. SHOE GOO hardens by solvent evaporation and forms an
immediate bond that is difficult to reposition after both adhesive-coated
surfaces are placed in contact with each other and sufficient pressure is
exerted to establish full contact.
Allow the repair to dry for 24 hours. Various materials will
require different drying times. Cure time increases with lower temperatures and
decreases with higher temperatures. Depending on the materials and the
temperature, maximum strength may not be reached for 48 to 72 hours.
Keep threads at the neck of the tube free of SHOE GOO
residue. To ensure easy cap removal, apply a thin coat of petroleum jelly to
the threads of the tube before replacing the cap.
Clean uncured adhesive with small amounts of acetone and
paint thinner. The adhesive will ball up and brush off. Cured material may be
removed by cutting or scraping.
Store unused SHOE GOO at room temperature with cap
tightened.
NOTE: SHOE GOO may damage finished surfaces. Avoid such
contact until SHOE GOO is completely dry.
Answers to Shoe GOO
Questions
Is there a special
application technique for shoe repair?
Shoe GOO is an adhesive specially formulated with extra
abrasion-resistance and thickness to extend the life of all kinds of shoes. If
a worn shoe has a hole that goes all the way through the sole, tape over the
hole inside the shoe before applying Shoe GOO to the outer sole; this will help
avoid creating a bump. The tape should be removed from the inside and all bumps
smoothed out within 2 hours, before the glue is completely hard.
Can Shoe GOO be used
as a waterproof sealant?
Yes, Shoe GOO is water resistant immediately upon
application. Apply Shoe GOO directly to the surface to be sealed. Use thin
coats of Shoe GOO to build a thick coating on the surface to be sealed,
allowing each layer to set 3 to 4 hours. This is especially ideal for smooth
surfaces, such as plastic, glass or ceramic. Shoe GOO hardens by solvent
evaporation, so allow time for thorough hardening to ensure proper bonding and
wear resistance.
How long does Shoe
GOO take to dry?
A full cure takes 24 to 72 hours, depending on the
surrounding environment. With lower temperatures and higher humidity, cure time
increases; with higher temperatures, cure time decreases. To speed drying time,
apply heat using a hand-held dryer set on low. Hold dryer at least 6 inches
from the surface.
What temperature
range does Shoe GOO withstand?
Shoe GOO can be applied in temperatures ranging from 50°F to
90°F. When cured, Shoe GOO can withstand temperatures between -40°F and 150°F.
Can Shoe GOO stick to
fishing waders and foul weather gear?
Some fisherman's waders and foul weather gear have a
water-repellent coating that must be removed before Shoe GOO will adhere. Scrub
the area with detergent and allow to dry. Roughen surface before applying Shoe
GOO. If the bond still pulls apart, the repair must be done on the inside
surface of the item, which is usually reinforced with fabric.
Soltrack Stick On Soles
|
Fits most Men and Women shoe sizes -
Trim to shape. Complete with Polyurethane Adhesive
Clean old, mark outline of shoe sole on the reverse side of the stick on sole with pen and cut out shape.
Spread a good even coat of adhesive to the shoe sole and also to the stick on sole. Leave to dry for 15 minutes.
Attached the stick on sole to the shoe sole
|
Men - Stick On Soles
£4.99
Women - Stick On Soles
£4.70
Shoe and Heels Repair Kits - (Match any shoe colour with this kit)
|
Repair any scrapes and damages on shoes and match any shoe colour. For the first time, scrapes and damages to any footwear can be restored to like-new without the expense of a shoe maker!
Restore damaged heels and shoes sides with this easy to use repair kit. Don't let those perfectly good shoes collect dust in the closet because the heel is damaged or scuffed up.
Our kit allows you to eliminate the damaged area, fill in the heel with a clear adhesive, and then match the colour and texture with our patented Liquid Leather.
This Kit comes with 7 Liquid Leather colours (Black, White, Brown, Yellow, Blue, Green and Red), mixing bottle, brush applicator, sand paper, grain/texture pack a colour guild mixing chart and special clear adhesive.
For example to get colour cream you take white and add a touch of brown, once happy with colour, you apply it to the area requiring repair
|
Shoe and Heel Repair Kit
£9.99